Bau des Gam_Bo_Prop / Building the Gam_Bo_Prop

Alles was Du selbst gebaut hast, hier herein. Das Projekt muss allerdings mit einem oder mehreren Parallax Propeller µC realisiert worden sein.
Benutzeravatar
TuxFan
Beiträge: 1022
Registriert: So 6. Sep 2009, 11:18

Re: Bau des Gam_Bo_Prop / Building the Gam_Bo_Prop

Beitrag von TuxFan »

Machen wir mit den SRAM-ICs weiter.

Baugruppe 6 :
Unterbaugruppe 6.4 :
1. Löten der drei Kondensatoren (C612, C613 und C614 100nF 0805)
2. Löten der zwei SRAM-Chips (IC641 und IC642 23K256 soic8)
3. Optische Kontrolle
Bild 1.
{
Nur wenn es benötigt wird :
SD-Modul mit SRAM und/oder FLASH Speicher
4. Löten von drei Kondensatoren (C1 bis C3 100nF 0805)
5. Löten eines SRAM-Chips (IC3 23K256 soic8)
6. Optische Kontrolle
7. Einsetzen des Moduls in den SD-Kartenhalter
Bild 2.
}
8. SRAM-Test mit Testprogramm 7 (GBP_SRAM_T7.spin)
Bild 3.
Wird fortgesetzt.....


Let's go with the SRAM Chips.

Unit 6 :
Subunit 6.4 :
1. Solder the three capacitors (C612, C613 and C614 100nF 0805)
2. Soldering the two SRAM chips (IC641 and IC642 23K256 SOIC8)
3. Optical control
Figure 1.
{
Only when it is needed:
SD-module with SRAM and / or FLASH memory
4. Soldering of three capacitors (C1 to C3 100nF 0805)
5. Soldering an SRAM chip (IC3 23K256 SOIC8)
6. optical control
7. Inserting the module into the SD card holder on the GBP-Motherboard
Figure 2.
}
8. SRAM-Test with Testprogram 7 (GBP_SRAM_T7.spin)
Figure 3.
To be continued ....
Dateianhänge
Bild 1 / Figure 1
Bild 1 / Figure 1
Bild 2 / Figure 2
Bild 2 / Figure 2
Bild 3 / Figure 3
Bild 3 / Figure 3
Zuletzt geändert von TuxFan am Do 22. Sep 2011, 15:29, insgesamt 1-mal geändert.
Wunder gibt es immer wieder.......
Benutzeravatar
TuxFan
Beiträge: 1022
Registriert: So 6. Sep 2009, 11:18

Re: Bau des Gam_Bo_Prop / Building the Gam_Bo_Prop

Beitrag von TuxFan »

Heute löten wir den Touchscreen Controller und testen seine Funktion.

Baugruppe 5 :
Unterbaugruppe 5.3 :

1. Löten des Controllers (IC531 AD7846 TSSOP16)
2. Optische Kontrolle der Anschlüsse des Controllers mit Lupe
3. Löten des Widerstandes (R531 100kOhm 0805)
4. Löten des Kondensators (C531 100nF 0805)
5. Optische Kontrolle
Bild 1.
6. Touchscreen-Test mit Testprogramm 8 (GBP_TOUCH_T8.spin)
Bild 2.

Nächstes mal muß nur noch der Flash-Speicher eingelötet und getestet werden.

Wird fortgesetzt.....



Today we solder the touch screen controller and test its functionality.

Unit 5:
Subunit 5.3:

1. Soldering of the controller (IC531 AD7846 TSSOP16)
2. Visual inspection of the connections of the controller with loupe
3. Soldering of the resistor (R531 100k 0805)
4. Solder the capacitor (C531 100nF 0805)
5. Optical inspection
Figure 1.
6. Touchscreen-Test with Testprogram 8 (GBP_TOUCH_T8.spin)
Figure 2.

Next time we just have to have the Flash memory soldered and tested.

To be continued .....
Dateianhänge
Bild 1 / Figure 1
Bild 1 / Figure 1
Bild 2 / Figure 2
Bild 2 / Figure 2
Zuletzt geändert von TuxFan am Do 22. Sep 2011, 15:31, insgesamt 1-mal geändert.
Wunder gibt es immer wieder.......
Benutzeravatar
TuxFan
Beiträge: 1022
Registriert: So 6. Sep 2009, 11:18

Re: Bau des Gam_Bo_Prop / Building the Gam_Bo_Prop

Beitrag von TuxFan »

Hallo!
Heute werden als letzte Bauteile die Flashspeicher eingelötet.

Baugruppe 6 :
Unterbaugruppe 6.4 :
1. Einlöten der zwei Flasch-Speicher (IC643 und IC644 AT25DF161 soic8 150mil)
2. Optische Prüfung
Bild 1.
3. FLASH-Test mit Testprogramm 9 (GBP_FLASH_T9.spin)
Bild 2 bis Bild 7.

So, das war dann der Zusammenbau der Elektronik. Nun folgt noch der Bau eines Gehäuses.

Wird fortgesetzt ......


Hello!
Today, as the last components to be soldered the flash memory.

Module 6:
Subassembly 6.4:
1. Soldering the two Flasch memory (IC643 and IC644 AT25DF161 SOIC8 150mil)
2. Optical testing
Figure 1.
3. FLASH-Test with Testprogram 9 (GBP_FLASH_T9.spin)
Figure 2 to 7.

So, that was then the assembly of the electronics. Now followed by the construction of a housing.

To be continued ......
Dateianhänge
Bild 1 / Figure 1<br />Flash-Memory 2 x 2 MB
Bild 1 / Figure 1
Flash-Memory 2 x 2 MB
Bild 2 / Figure 2<br />Wählen des Chips am SPI-BUS / Coose a chip on SPI-BUS
Bild 2 / Figure 2
Wählen des Chips am SPI-BUS / Coose a chip on SPI-BUS
Bild 3 / Figure 3<br />Lesen der JEDEC-ID / Reading the JEDEC-ID
Bild 3 / Figure 3
Lesen der JEDEC-ID / Reading the JEDEC-ID
Bild 4 / Figure 4<br />Schreiben des Speichers / Writing the memory<br />Startaddress 1000, value 235 ($EB), 100 bytes<br />(Eingabe mit Bildschirmtastatur / Input with on screen keyboard)
Bild 4 / Figure 4
Schreiben des Speichers / Writing the memory
Startaddress 1000, value 235 ($EB), 100 bytes
(Eingabe mit Bildschirmtastatur / Input with on screen keyboard)
Bild 5 / Figure 5<br />Lesen der Speicherplätze, Eingabe / Reading the 100 byte memory, input
Bild 5 / Figure 5
Lesen der Speicherplätze, Eingabe / Reading the 100 byte memory, input
Bild 6 / Figure 6<br />Hexdump der 100 Speicherplätze / Hexdump of the 100 byte memory
Bild 6 / Figure 6
Hexdump der 100 Speicherplätze / Hexdump of the 100 byte memory
Bild 7 / Figure 7<br />Chip löschen / Chip erase
Bild 7 / Figure 7
Chip löschen / Chip erase
Zuletzt geändert von TuxFan am Do 22. Sep 2011, 15:33, insgesamt 1-mal geändert.
Wunder gibt es immer wieder.......
Benutzeravatar
TuxFan
Beiträge: 1022
Registriert: So 6. Sep 2009, 11:18

Re: Bau des Gam_Bo_Prop / Building the Gam_Bo_Prop

Beitrag von TuxFan »

Hallo!
Heute veröffentliche ich den Schaltplan, das Board und die Stückliste. In der Stückliste sind die Händler angegeben, bei denen ich die Teile bestellt habe. Dazu habe ich die Bestellnummern der Teile angegeben.
Ich hoffe das alles fehlerfrei ist. Da ein Teil der Schaltung unter der Creative Commons Lizenz veröffentlicht wurde, habe ich die ganze Schaltung unter der Creative Commons Lizenz veröffentlicht.
Falls jemand die Schaltung oder das Board für seine Zwecke ändert, möchte ich darauf hinweisen, daß das Board von Hand gerouted worden ist.
Als nächstes werden dann die Testprogramme veröffentlicht.

Wird fortgesetzt......


Hello!
Today I publish the schematics, the board and the BOM. In the BOM the dealers are given, where I ordered the parts. In addition I have given the order numbers of the parts.
I hope that everything is correct. As part of the circuit under the Creative Commons license was issued, I published the whole circuit under a Creative Commons license.
If someone changes the circuit or board for its purposes, I should point out that the board has been routed by hand.
Next the test programs will be published.

To be continued ......
Dateianhänge
Gam_Bo_Prop_V1_R1.zip
(134.17 KiB) 630-mal heruntergeladen
Wunder gibt es immer wieder.......
Benutzeravatar
TuxFan
Beiträge: 1022
Registriert: So 6. Sep 2009, 11:18

Re: Bau des Gam_Bo_Prop / Building the Gam_Bo_Prop

Beitrag von TuxFan »

Hallo!
Ich habe ganz vergessen die Platine für den Batteriehalter zu veröffentlichen. Diese Platine wird zwei mal benötigt. Dazu braucht man noch zwei Spiralfedern.

Wird fortgesetzt.........


Hello!
I forgot to publish the board for the battery holder. This board is needed twice. This requires two springs.

To be continued .........
Dateianhänge
BAT_GBP_2AAA.zip
(4.4 KiB) 602-mal heruntergeladen
Wunder gibt es immer wieder.......
Benutzeravatar
TuxFan
Beiträge: 1022
Registriert: So 6. Sep 2009, 11:18

Re: Bau des Gam_Bo_Prop / Building the Gam_Bo_Prop

Beitrag von TuxFan »

Hallo!
Ein paar Änderungen habe ich in dem Thread vorgenommen und die einzelnen Testprogramme eingetragen.
Als Anhang noch die gesammelten Testprogramme als ZIP-File

Hello!
A few changes I've made in the thread and added the individual test programs.
As an appendix, the collected test programs as ZIP-File
Dateianhänge
GBP-Testprograms.zip
(93.95 KiB) 609-mal heruntergeladen
Wunder gibt es immer wieder.......
Antworten