Testing the Hive Board after section one
-
- Beiträge: 4
- Registriert: Do 23. Jan 2014, 20:52
Testing the Hive Board after section one
I am currently building the hive Board, rev 14 2011. I have the first step done. When I plug-in power and test the pin headers at the right side of the board, if I touch ground and 3.3 I get 3.3, but if I touch ground and 5.0 I still get 3.3. What Jumpers need to be set on the pin-header by the power jack and am I testing correctly? I have the middle jack jumpered by the power jack. It's not clear what all these pin headers do. If you could let me know that, it would be great. Also what needs to be set to test would be great too.
Thanks
Greg
Thanks
Greg
- drohne235
- Administrator
- Beiträge: 2284
- Registriert: So 24. Mai 2009, 10:35
- Wohnort: Lutherstadt Wittenberg
- Kontaktdaten:
Re: Testing the Hive Board after section one
Put the following four Jumper:
SW (Power Switch)
GND
3,3V
5V
Important: The power LED is needed as base load! Now you can measure.
SW (Power Switch)
GND
3,3V
5V
Important: The power LED is needed as base load! Now you can measure.
"Ob Sie denken, dass Sie es können, oder ob Sie denken, dass Sie es nicht können - in beiden Fällen haben Sie recht." Henry Ford
-
- Beiträge: 4
- Registriert: Do 23. Jan 2014, 20:52
Re: Testing the Hive Board after section one
I'm still having trouble with the board.
1) The LED heats up over time and starts to go on and off.
2) Still don't know where to put my leads to test the voltage.
This first attachment is so you can see the components I put on.
Including the LED.
The second attachment is to show the Zener Diode in the far corner of the board.
This is my soldering job. No soldering bridges that I can detect, but the flux is also still on the board.
Thanks in advance.
Greg
1) The LED heats up over time and starts to go on and off.
2) Still don't know where to put my leads to test the voltage.
This first attachment is so you can see the components I put on.
Including the LED.
The second attachment is to show the Zener Diode in the far corner of the board.
This is my soldering job. No soldering bridges that I can detect, but the flux is also still on the board.
Thanks in advance.
Greg
-
- Beiträge: 4
- Registriert: Do 23. Jan 2014, 20:52
Re: Testing the Hive Board after section one
Here is also my BOM in case you are interested in going out to DigiKey.com and looking at the datasheets.
Thanks
Greg
Also my notes.
Thanks
Greg
Also my notes.
Re: Testing the Hive Board after section one
Look at http://drohne0332.blogspot.co.at/2012/0 ... rgung.html - there is a nice image between which pins you should measure the voltage (between the marked GND pin and the marked 3,3V or 5V pin).AdamantiumOgre hat geschrieben:I'm still having trouble with the board.
1) The LED heats up over time and starts to go on and off.
2) Still don't know where to put my leads to test the voltage.
Drohne 0348 starb im mutigem Kampf gegen den Lötkolben einen Heldentod. Die Assimilierung geht mit Drohne 0371 weiter.
- PIC18F2550
- Beiträge: 2832
- Registriert: Fr 30. Sep 2011, 13:08
Re: Testing the Hive Board after section one
Attention!
Use rosin for soldering. http://en.wikipedia.org/wiki/Flux_%28metallurgy%29
Acid in the flux destroys the interconnects !!!
Sorry i use google to translate.![Tippen :TIPPEN](./images/smilies/smilie_girl_173.gif)
Use rosin for soldering. http://en.wikipedia.org/wiki/Flux_%28metallurgy%29
![Ausruf :!:](./images/smilies/icon_exclaim.gif)
Acid in the flux destroys the interconnects !!!
Sorry i use google to translate.
![Tippen :TIPPEN](./images/smilies/smilie_girl_173.gif)
Gruß
PIC18F2550
drone265/278
Barbarus hic ergo sum, quia non intellegor ulli.
Ein Barbar bin ich hier, da ich von keinem verstanden werde.
ʎɐqǝ ıǝq ɹnʇɐʇsɐʇ ǝuıǝ ɹǝpǝıʍ ǝıu ǝɟnɐʞ ɥɔı ´uuɐɯ ɥo
PIC18F2550
drone265/278
Barbarus hic ergo sum, quia non intellegor ulli.
Ein Barbar bin ich hier, da ich von keinem verstanden werde.
ʎɐqǝ ıǝq ɹnʇɐʇsɐʇ ǝuıǝ ɹǝpǝıʍ ǝıu ǝɟnɐʞ ɥɔı ´uuɐɯ ɥo
-
- Beiträge: 4
- Registriert: Do 23. Jan 2014, 20:52
Re: Testing the Hive Board after section one
Actually I'm using Oatey No. 5 Lead Free Solder paste. I don't know if that is more of a flux or a rosin. I will throw this away, clean the board with Alcohol and buy some Rosin.
The test points work, so I'm going to ignore the LED heating up for now and work on the rest of the board. Thanks PIC18F2550 and Nubok
The test points work, so I'm going to ignore the LED heating up for now and work on the rest of the board. Thanks PIC18F2550 and Nubok
- PIC18F2550
- Beiträge: 2832
- Registriert: Fr 30. Sep 2011, 13:08
Re: Testing the Hive Board after section one
NOT FOR USE
WITH ALUMINUM, STAINLESS STEEL OR MAGNESIUM.
DO NOT USE ON ELECTRICAL PARTS.
1. All desoldering again. (Otherwise, it can not completely remove the flux.)
2. Wash the components with 60 ° C hot water.(with dishwashing liquid to dissolve the fat proportion) min 5 Minuten.
3. Rinse with clear water.
4. Let it dry 24H.
5. Components solder -> the proper solder. http://www.reichelt.de/Loetzinn/L-TZINN ... =L%F6TZINN
A proper solder joint, Silver shines.
Good desires to succeed.![Schrauben :SCHRAUBEN](./images/smilies/smilie_be_110.gif)
WITH ALUMINUM, STAINLESS STEEL OR MAGNESIUM.
DO NOT USE ON ELECTRICAL PARTS.
![Traurig :(](./images/smilies/icon_e_sad.gif)
2. Wash the components with 60 ° C hot water.(with dishwashing liquid to dissolve the fat proportion) min 5 Minuten.
3. Rinse with clear water.
4. Let it dry 24H.
5. Components solder -> the proper solder. http://www.reichelt.de/Loetzinn/L-TZINN ... =L%F6TZINN
A proper solder joint, Silver shines.
![Daumen hoch :DAUMENHOCH](./images/smilies/smilie_girl_020.gif)
Good desires to succeed.
![Schrauben :SCHRAUBEN](./images/smilies/smilie_be_110.gif)
Gruß
PIC18F2550
drone265/278
Barbarus hic ergo sum, quia non intellegor ulli.
Ein Barbar bin ich hier, da ich von keinem verstanden werde.
ʎɐqǝ ıǝq ɹnʇɐʇsɐʇ ǝuıǝ ɹǝpǝıʍ ǝıu ǝɟnɐʞ ɥɔı ´uuɐɯ ɥo
PIC18F2550
drone265/278
Barbarus hic ergo sum, quia non intellegor ulli.
Ein Barbar bin ich hier, da ich von keinem verstanden werde.
ʎɐqǝ ıǝq ɹnʇɐʇsɐʇ ǝuıǝ ɹǝpǝıʍ ǝıu ǝɟnɐʞ ɥɔı ´uuɐɯ ɥo
- drohne235
- Administrator
- Beiträge: 2284
- Registriert: So 24. Mai 2009, 10:35
- Wohnort: Lutherstadt Wittenberg
- Kontaktdaten:
Re: Testing the Hive Board after section one
Perhaps as useful info - how to Solder: http://www.youtube.com/watch?v=I_NU2ruzyc4
Edit:
Please check:
IC1 = L4940 V5
IC2 = LM2937 ET 3,3
Are the parts reversed?
Edit:
Please check:
IC1 = L4940 V5
IC2 = LM2937 ET 3,3
Are the parts reversed?
"Ob Sie denken, dass Sie es können, oder ob Sie denken, dass Sie es nicht können - in beiden Fällen haben Sie recht." Henry Ford